Author: Sukhikh, L.G.
Paper Title Page
WEPB10 Grating Scanner for Measurement of Micron-size Beam Profiles 448
 
  • L.G. Sukhikh, A. Potylitsyn, S.A. Strokov
    TPU, Tomsk, Russia
  • G. Kube, K. Wittenburg
    DESY, Hamburg, Germany
 
  Funding: The work was partly supported by the program ‘‘Nauka' of the Russian Ministry of Education and Science, grant # 3.1903.2017
Wire scanners are widely used for transverse beam size diagnostics. The minimum detectable beam size is affected by the diameter of a single wire. The smallest carbon or tungsten wires used so far have diameters of about 4 microns. With the development of modern electron accelerators and the demands from future linear electron-positron colliders, sub-micron beam sizes have to be resolved. In order to increase the resolution, the decrease of the wire diameter is required. The authors of Ref. * proposed to manufacture thin gold stripes of rectangular shape (widths are equal to 1 µm or 2 µm and height is equal to 3 µm) on Si3N4 membrane. We propose to use another arrangement of gold stripes with varying period on a Si substrate. A set of 11 stripes with 1 µm width and 10 micron height with varying gap width in the range 3-0.25 µm ("grating scanner") was simulated by using an analytical model and by the Geant4 code. By moving this scanner across the beam one could measure the Bremsstrahlung yield vs. the coordinate, resulting in an oscillating dependence. The visibility of the resulting image allows defining the beam sizes in the range of 0.5-1.5 µm for the proposed scanner parameters.
* S. Borrelli et al., "Generation and Measurement of Sub-Micrometer Relativistic Electron Beams", arXiv:1804.04252v1 [physics.acc-ph] 11 Apr 2018
 
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPB10  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEPB11 Spatial Resolution Improvement of OTR Monitors by Off-axis Light Collection 451
 
  • A. Potylitsyn, A.I. Novokshonov, L.G. Sukhikh
    TPU, Tomsk, Russia
  • G. Kube, A.I. Novokshonov
    DESY, Hamburg, Germany
 
  Funding: The work was partly supported by the program "Nauka" of the Russian Ministry of Education and Science, grant #3.1903.2017
The spatial resolution of an OTR monitor for electron beam profile diagnostics is determined by the resolution of the optical system and by the Point Spread Function (PSF) representing the single electron image. In the image plane, the PSF has a typical lobe-shape distribution with an inter-peak distance depending on wavelength and lens aperture ratio [*]. For a beam with a transverse rms size smaller than the distance, the reconstruction of the beam profile has several difficulties [**, ***]. We propose to reduce the PSF contribution and to improve the spatial resolution of an OTR monitor simply by rotating the lens optical axis with respect to the specular reflection direction. If the difference between the rotational angle and the lens aperture is much larger than the inverse Lorentz factor, the PSF has a Gaussian-like distribution which matches practically with the Airy distribution. Thus the resolution depends on wavelength and lens aperture. In principle, for lens apertures in the order of 0.1 rad such an approach should allow to measure beam sizes comparable to the wavelength of observation, using a simple deconvolution procedure for the measured image and the PSF.
* M. Castellano, V.Verzilov, Phys. Rev. ST-AB, 1 (1998).
** K.Kruchinin, S.T.Boogert, P.Karataev et al., Proc. IBIC 2013 (2013).
*** L.G. Sukhikh, A.P. Potylitsyn, G. Kube, Phys. Rev. AB 20 (2017).
 
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPB11  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)